загорается "check engine"
-
- Рядовой
- Сообщения: 10
- Зарегистрирован: 14 окт 2015, 22:50
- Город: Минск
- Авто: ASX 1,8 2WD серебристый
- Пробег: 95000
- Прошлый авто: KIA
- Благодарил (а): 1 раз
загорается "check engine"
#1Всем доброго времени суток! Являюсь владельцем ASX около полугода. Машинка 2011 г.в.V1,8. На данный момент пробег около 71 тыс. км В принципе машинка всем устраивает. Но есть одно "но". Около месяца назад загорелась лампочка "check engine". Диагностика показала ошибку лябда-зонд 2 (стоит после катализатора). Стерли ошибку. Заправлялся на другой АЗС. Лампочка не загоралась. На 70 тыс. заменил масло ДВС и свечи. Проехал около 700 км и вдруг ни с того, ни с сего "check" загорелся вновь и спустя 300км пути погас. С чем можно связать причину такого поведения и какие действия посоветуете? Заранее всем спасибо за дельный совет и удачи на дороге!
- hardman
- Старший лейтенант
- Сообщения: 548
- Зарегистрирован: 05 окт 2012, 16:47
- Город: Москва
- Авто: ASX S11 Dark Blue
- Пробег: 297000
- Прошлый авто: KIA CeeD hatchback KIA Rio JB, Opel Astra
- Благодарил (а): 38 раз
- Поблагодарили: 74 раза
загорается "check engine"
#2У меня была схожая проблема на предыдущем авто, так же заправился не важным бензином. Пока не поменял фильтр тонкой очистки топлива ошибка периодически выскакивала....
Вот такие дела....
- mobileman
- Майор
- Сообщения: 1119
- Зарегистрирован: 29 окт 2012, 13:37
- Город: Москва
- Авто: Lancer X, Audi A3
- Пробег: 110000
- Прошлый авто: Lancer IX
- :
- Благодарил (а): 143 раза
- Поблагодарили: 391 раз
загорается "check engine"
#3voyager писал(а):Около месяца назад загорелась лампочка "check engine". Диагностика показала ошибку лябда-зонд 2 ........
Заранее всем спасибо за дельный совет и удачи на дороге!
Код ошибки какой ? Их там по ДК 2 около пяти штук...
- инжектор+
- Майор
- Сообщения: 1459
- Зарегистрирован: 13 дек 2011, 01:52
- Город: красная поляна
- Авто: ASX S08 MT БЕЛЫЙ
- :
- Благодарил (а): 100 раз
- Поблагодарили: 199 раз
загорается "check engine"
#4А чем тема старая с ошибками неустроила
viewtopic.php?f=13&t=584&start=345
viewtopic.php?f=13&t=584&start=345
- инжектор+
- Майор
- Сообщения: 1459
- Зарегистрирован: 13 дек 2011, 01:52
- Город: красная поляна
- Авто: ASX S08 MT БЕЛЫЙ
- :
- Благодарил (а): 100 раз
- Поблагодарили: 199 раз
загорается "check engine"
#7voyager писал(а):Код ошибки был P0137
Для России:
Code No. P0137: Oxygen Sensor (rear) Circuit Low Voltage <Vehicles for Russia>
OPERATION
The sensor signal is inputted to the engine-ECU (terminal No. 40) from the oxygen sensor (rear) output terminal (terminal No. 3).
The engine-ECU (terminal No. 41) applies an offset voltage of 0.5 V to the oxygen sensor (rear) (terminal No. 4).
FUNCTION
The oxygen sensor (rear) converts the concentration of oxygen in the exhaust emission into a voltage and inputs the signal to the engine-ECU.
When the air-fuel ratio is richer than the theoretical air-fuel ratio, the oxygen sensor (rear) outputs a voltage of about 1 V. When it is leaner than the theoretical air-fuel ratio, it outputs a voltage of about 0 V.
In response to the signal, the engine-ECU controls the fuel injection amount so that the air-fuel ratio can be equivalent to the theoretical air-fuel ratio.
TROUBLE JUDGMENT
Check Conditions
Oxygen sensor (rear) offset voltage is more than 0.4 V and is less than 0.6 V.
Battery positive voltage is more than 11 V and is less than 16.5 V.
More than 3 minutes have passed since the engine starting sequence was completed.
Judgement Criterion
Oxygen sensor (rear) output voltage is less than 0.2 V for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION
None
PROBABLE CAUSES
Failed oxygen sensor (rear)
Open/short circuit or harness damage in oxygen sensor (rear) circuit or loose connector contact
Failed engine-ECU
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III data list
Data list reference table (Refer to ).
Item AD: Oxygen sensor (rear)
Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Go to Step 2.
STEP 2. Connector check: D-38 oxygen sensor (rear) connector
Q. Is the check result normal?
Go to Step 3.
Repair or replace the connector.
STEP 3. Perform voltage measurement at D-38 oxygen sensor (rear) connector.
Disconnect connector, and measure at harness side.
Ignition switch: ON
Voltage between terminal No. 4 and earth.
OK: 0.4 - 0.6 V
Q. Is the check result normal?
Go to Step 7.
Go to Step 4.
STEP 4. Connector check: B-26 engine-ECU connector
Q. Is the check result normal?
Go to Step 5.
Repair or replace the connector.
STEP 5. Check harness between D-38 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.
note Before checking harness, check intermediate connectors A-17 and C-15, and repair if necessary.
Check earthing line for open/short circuit.
Q. Is the check result normal?
Go to Step 6.
Repair the damaged harness wire.
STEP 6. M.U.T.-III data list
Data list reference table (Refer to ).
Item AD: Oxygen sensor (rear)
Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Replace the engine-ECU.
STEP 7. Connector check: B-26 engine-ECU connector
Q. Is the check result normal?
Go to Step 8.
Repair or replace the connector.
STEP 8. Check harness between D-38 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.
note Before checking harness, check intermediate connectors A-17 and C-15, and repair if necessary.
Check earthing line for damage.
Q. Is the check result normal?
Go to Step 9.
Repair the damaged harness wire.
STEP 9. Perform voltage measurement at D-38 oxygen sensor (rear) connector.
Use special tool test harness (MB991658) to connect connector, and measure at pick-up harness.
Transmission: 2nd speed
Drive with wide open throttle
Engine: 3,500 r/min or more
Voltage between terminal No. 3 and earth.
OK:
The output voltage should be 1.1 - 1.5 V.
Q. Is the check result normal?
Go to Step 11.
Go to Step 10.
STEP 10. Check oxygen sensor (rear) itself.
Oxygen sensor check (Refer to ).
Q. Is the check result normal?
Check intermediate connectors A-17 and C-15, and repair if necessary. If intermediate connectors are normal, check and repair harness between D-38 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.
Check output line for short circuit.
Replace oxygen sensor (rear).
STEP 11. Check harness between D-38 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.
note Before checking harness, check intermediate connectors A-17 and C-15, and repair if necessary.
Check output line for open circuit and damage.
Q. Is the check result normal?
Go to Step 6.
Repair the damaged harness wire.
Yandex.Metrika ???????@Mail.ru??
MMC-Manuals.ru
- инжектор+
- Майор
- Сообщения: 1459
- Зарегистрирован: 13 дек 2011, 01:52
- Город: красная поляна
- Авто: ASX S08 MT БЕЛЫЙ
- :
- Благодарил (а): 100 раз
- Поблагодарили: 199 раз
загорается "check engine"
#8Для остального мира
Code No. P0137: Oxygen Sensor (rear) Circuit Low Voltage <Except vehicles for Russia>
OPERATION
The sensor signal is inputted to the engine-ECU (terminal No. 40) from the oxygen sensor (rear) output terminal (terminal No. 3).
The engine-ECU (terminal No. 41) applies an offset voltage of 0.5 V to the oxygen sensor (rear) (terminal No. 4).
FUNCTION
The oxygen sensor (rear) converts the concentration of oxygen in the exhaust emission into a voltage and inputs the signal to the engine-ECU.
When the air-fuel ratio is richer than the theoretical air-fuel ratio, the oxygen sensor (rear) outputs a voltage of about 1 V. When it is leaner than the theoretical air-fuel ratio, it outputs a voltage of about 0 V.
In response to the signal, the engine-ECU controls the fuel injection amount so that the air-fuel ratio can be equivalent to the theoretical air-fuel ratio.
TROUBLE JUDGMENT
Check Conditions
Oxygen sensor (rear) offset voltage is more than 0.4 V and is less than 0.6 V.
Battery positive voltage is more than 11 V and is less than 16.5 V.
More than 3 minutes have passed since the engine starting sequence was completed.
Judgement Criterion
Oxygen sensor (rear) output voltage is less than 0.2 V for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION
None
PROBABLE CAUSES
Failed oxygen sensor (rear)
Open/short circuit or harness damage in oxygen sensor (rear) circuit or loose connector contact
Failed engine-ECU
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III data list
Data list reference table (Refer to ).
Item AD: Oxygen sensor (rear)
Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Go to Step 2.
STEP 2. Connector check: C-36 oxygen sensor (rear) connector
Q. Is the check result normal?
Go to Step 3.
Repair or replace the connector.
STEP 3. Perform voltage measurement at C-36 oxygen sensor (rear) connector.
Disconnect connector, and measure at harness side.
Ignition switch: ON
Voltage between terminal No. 4 and earth.
OK: 0.4 - 0.6 V
Q. Is the check result normal?
Go to Step 7.
Go to Step 4.
STEP 4. Connector check: B-26 engine-ECU connector
Q. Is the check result normal?
Go to Step 5.
Repair or replace the connector.
STEP 5. Check harness between C-36 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.
note Before checking harness, check intermediate connector A-17, and repair if necessary.
Check earthing line for open/short circuit.
Q. Is the check result normal?
Go to Step 6.
Repair the damaged harness wire.
STEP 6. M.U.T.-III data list
Data list reference table (Refer to ).
Item AD: Oxygen sensor (rear)
Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Replace the engine-ECU.
STEP 7. Connector check: B-26 engine-ECU connector
Q. Is the check result normal?
Go to Step 8.
Repair or replace the connector.
STEP 8. Check harness between C-36 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.
note Before checking harness, check intermediate connector A-17, and repair if necessary.
Check earthing line for damage.
Q. Is the check result normal?
Go to Step 9.
Repair the damaged harness wire.
STEP 9. Perform voltage measurement at C-36 oxygen sensor (rear) connector.
Use special tool test harness (MB991658) to connect connector, and measure at pick-up harness.
Transmission: 2nd speed
Drive with wide open throttle
Engine: 3,500 r/min or more
Voltage between terminal No. 3 and earth.
OK:
The output voltage should be 1.1 - 1.5 V.
Q. Is the check result normal?
Go to Step 11.
Go to Step 10.
STEP 10. Check oxygen sensor (rear) itself.
Oxygen sensor check (Refer to ).
Q. Is the check result normal?
Check intermediate connector A-17, and repair if necessary. If intermediate connector is normal, check and repair harness between C-36 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.
Check output line for short circuit.
Replace oxygen sensor (rear).
STEP 11. Check harness between C-36 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.
note Before checking harness, check intermediate connector A-17, and repair if necessary.
Check output line for open circuit and damage.
Q. Is the check result normal?
Go to Step 6.
Repair the damaged harness wire.
Yandex.Metrika ???????@Mail.ru??
MMC-Manuals.ru
Code No. P0137: Oxygen Sensor (rear) Circuit Low Voltage <Except vehicles for Russia>
OPERATION
The sensor signal is inputted to the engine-ECU (terminal No. 40) from the oxygen sensor (rear) output terminal (terminal No. 3).
The engine-ECU (terminal No. 41) applies an offset voltage of 0.5 V to the oxygen sensor (rear) (terminal No. 4).
FUNCTION
The oxygen sensor (rear) converts the concentration of oxygen in the exhaust emission into a voltage and inputs the signal to the engine-ECU.
When the air-fuel ratio is richer than the theoretical air-fuel ratio, the oxygen sensor (rear) outputs a voltage of about 1 V. When it is leaner than the theoretical air-fuel ratio, it outputs a voltage of about 0 V.
In response to the signal, the engine-ECU controls the fuel injection amount so that the air-fuel ratio can be equivalent to the theoretical air-fuel ratio.
TROUBLE JUDGMENT
Check Conditions
Oxygen sensor (rear) offset voltage is more than 0.4 V and is less than 0.6 V.
Battery positive voltage is more than 11 V and is less than 16.5 V.
More than 3 minutes have passed since the engine starting sequence was completed.
Judgement Criterion
Oxygen sensor (rear) output voltage is less than 0.2 V for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION
None
PROBABLE CAUSES
Failed oxygen sensor (rear)
Open/short circuit or harness damage in oxygen sensor (rear) circuit or loose connector contact
Failed engine-ECU
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III data list
Data list reference table (Refer to ).
Item AD: Oxygen sensor (rear)
Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Go to Step 2.
STEP 2. Connector check: C-36 oxygen sensor (rear) connector
Q. Is the check result normal?
Go to Step 3.
Repair or replace the connector.
STEP 3. Perform voltage measurement at C-36 oxygen sensor (rear) connector.
Disconnect connector, and measure at harness side.
Ignition switch: ON
Voltage between terminal No. 4 and earth.
OK: 0.4 - 0.6 V
Q. Is the check result normal?
Go to Step 7.
Go to Step 4.
STEP 4. Connector check: B-26 engine-ECU connector
Q. Is the check result normal?
Go to Step 5.
Repair or replace the connector.
STEP 5. Check harness between C-36 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.
note Before checking harness, check intermediate connector A-17, and repair if necessary.
Check earthing line for open/short circuit.
Q. Is the check result normal?
Go to Step 6.
Repair the damaged harness wire.
STEP 6. M.U.T.-III data list
Data list reference table (Refer to ).
Item AD: Oxygen sensor (rear)
Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Replace the engine-ECU.
STEP 7. Connector check: B-26 engine-ECU connector
Q. Is the check result normal?
Go to Step 8.
Repair or replace the connector.
STEP 8. Check harness between C-36 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.
note Before checking harness, check intermediate connector A-17, and repair if necessary.
Check earthing line for damage.
Q. Is the check result normal?
Go to Step 9.
Repair the damaged harness wire.
STEP 9. Perform voltage measurement at C-36 oxygen sensor (rear) connector.
Use special tool test harness (MB991658) to connect connector, and measure at pick-up harness.
Transmission: 2nd speed
Drive with wide open throttle
Engine: 3,500 r/min or more
Voltage between terminal No. 3 and earth.
OK:
The output voltage should be 1.1 - 1.5 V.
Q. Is the check result normal?
Go to Step 11.
Go to Step 10.
STEP 10. Check oxygen sensor (rear) itself.
Oxygen sensor check (Refer to ).
Q. Is the check result normal?
Check intermediate connector A-17, and repair if necessary. If intermediate connector is normal, check and repair harness between C-36 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.
Check output line for short circuit.
Replace oxygen sensor (rear).
STEP 11. Check harness between C-36 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.
note Before checking harness, check intermediate connector A-17, and repair if necessary.
Check output line for open circuit and damage.
Q. Is the check result normal?
Go to Step 6.
Repair the damaged harness wire.
Yandex.Metrika ???????@Mail.ru??
MMC-Manuals.ru
- mobileman
- Майор
- Сообщения: 1119
- Зарегистрирован: 29 окт 2012, 13:37
- Город: Москва
- Авто: Lancer X, Audi A3
- Пробег: 110000
- Прошлый авто: Lancer IX
- :
- Благодарил (а): 143 раза
- Поблагодарили: 391 раз
загорается "check engine"
#9voyager
для начала проверьте проводку датчика под днищем на предмет повреждения изоляции...
для начала проверьте проводку датчика под днищем на предмет повреждения изоляции...
- hardman
- Старший лейтенант
- Сообщения: 548
- Зарегистрирован: 05 окт 2012, 16:47
- Город: Москва
- Авто: ASX S11 Dark Blue
- Пробег: 297000
- Прошлый авто: KIA CeeD hatchback KIA Rio JB, Opel Astra
- Благодарил (а): 38 раз
- Поблагодарили: 74 раза
загорается "check engine"
#11Коллеги, а если человек с английским не дружит?:) форум мне кажется на то он и форум чтобы дать по возможности совет а не отсылать лопатить ERROR LIST
Вот такие дела....
- mobileman
- Майор
- Сообщения: 1119
- Зарегистрирован: 29 окт 2012, 13:37
- Город: Москва
- Авто: Lancer X, Audi A3
- Пробег: 110000
- Прошлый авто: Lancer IX
- :
- Благодарил (а): 143 раза
- Поблагодарили: 391 раз
загорается "check engine"
#12hardman писал(а):Коллеги, а если человек с английским не дружит?:)
Существует масса онлайн-переводчиков в интернете. Да, многие из них переводят "коряво", но уловить смысл про типовые причины возникновения кода неисправности вполне возможно.
P.S. Советов можно дать много....Проверить проводку датчика. Если изоляция сигнальных проводов повреждена и будет "коротить" на корпус авто, то можно словить P 0137.
Можно проверить опорное напряжение, которое ЭБУ двигателя выдает на датчик. Оно должно быть ~0.5 v... Сделать это можно с помощью мультиметра в подкапотном блоке предохранителей, измерив напряжение на соответствующих проводах белого большого разъема при включенном зажигании.Схемы из мануала, ссылку на который уже дали - в помощь.
- инжектор+
- Майор
- Сообщения: 1459
- Зарегистрирован: 13 дек 2011, 01:52
- Город: красная поляна
- Авто: ASX S08 MT БЕЛЫЙ
- :
- Благодарил (а): 100 раз
- Поблагодарили: 199 раз
загорается "check engine"
#13Если человек не дружит с английским, не разбирается в устройстве авто, никогда не пользовался мультиметром(и не хочет этому научиться) - совет может быть один: ищите хорошего диагноста.
Вернуться в «Вопросы по электрике»
Кто сейчас на конференции
Сейчас этот форум просматривают: нет зарегистрированных пользователей и 5 гостей