загорается "check engine"

Электрооборудование
voyager
Рядовой
Рядовой
Сообщения: 10
Зарегистрирован: 14 окт 2015, 22:50
Город: Минск
Авто: ASX 1,8 2WD серебристый
Пробег: 95000
Прошлый авто: KIA
Благодарил (а): 1 раз

загорается "check engine"

#1

Сообщение voyager » 12 май 2016, 11:46

Всем доброго времени суток! Являюсь владельцем ASX около полугода. Машинка 2011 г.в.V1,8. На данный момент пробег около 71 тыс. км В принципе машинка всем устраивает. Но есть одно "но". Около месяца назад загорелась лампочка "check engine". Диагностика показала ошибку лябда-зонд 2 (стоит после катализатора). Стерли ошибку. Заправлялся на другой АЗС. Лампочка не загоралась. На 70 тыс. заменил масло ДВС и свечи. Проехал около 700 км и вдруг ни с того, ни с сего "check" загорелся вновь и спустя 300км пути погас. С чем можно связать причину такого поведения и какие действия посоветуете? Заранее всем спасибо за дельный совет и удачи на дороге!

Аватара пользователя
hardman
Старший лейтенант
Старший лейтенант
Сообщения: 548
Зарегистрирован: 05 окт 2012, 16:47
Город: Москва
Авто: ASX S11 Dark Blue
Пробег: 297000
Прошлый авто: KIA CeeD hatchback KIA Rio JB, Opel Astra
Благодарил (а): 38 раз
Поблагодарили: 74 раза

загорается "check engine"

#2

Сообщение hardman » 12 май 2016, 11:53

У меня была схожая проблема на предыдущем авто, так же заправился не важным бензином. Пока не поменял фильтр тонкой очистки топлива ошибка периодически выскакивала....
Вот такие дела....

Аватара пользователя
mobileman
Майор
Майор
Сообщения: 1114
Зарегистрирован: 29 окт 2012, 13:37
Город: Москва
Авто: Lancer X, Audi A3
Пробег: 110000
Прошлый авто: Lancer IX
:
Золотая звезда I степени Золотые руки
Благодарил (а): 141 раз
Поблагодарили: 391 раз

загорается "check engine"

#3

Сообщение mobileman » 12 май 2016, 12:57

voyager писал(а):Около месяца назад загорелась лампочка "check engine". Диагностика показала ошибку лябда-зонд 2 ........
Заранее всем спасибо за дельный совет и удачи на дороге!

Код ошибки какой ? Их там по ДК 2 около пяти штук...

Аватара пользователя
инжектор+
Майор
Майор
Сообщения: 1459
Зарегистрирован: 13 дек 2011, 01:52
Город: красная поляна
Авто: ASX S08 MT БЕЛЫЙ
:
Всегда готов
Благодарил (а): 100 раз
Поблагодарили: 199 раз

загорается "check engine"

#4

Сообщение инжектор+ » 12 май 2016, 13:34

А чем тема старая с ошибками неустроила
viewtopic.php?f=13&t=584&start=345 :!:

voyager
Рядовой
Рядовой
Сообщения: 10
Зарегистрирован: 14 окт 2015, 22:50
Город: Минск
Авто: ASX 1,8 2WD серебристый
Пробег: 95000
Прошлый авто: KIA
Благодарил (а): 1 раз

загорается "check engine"

#5

Сообщение voyager » 12 май 2016, 13:42

Код ошибки был P0137

voyager
Рядовой
Рядовой
Сообщения: 10
Зарегистрирован: 14 окт 2015, 22:50
Город: Минск
Авто: ASX 1,8 2WD серебристый
Пробег: 95000
Прошлый авто: KIA
Благодарил (а): 1 раз

загорается "check engine"

#6

Сообщение voyager » 12 май 2016, 13:51

viewtopic.php?f=13&t=584&start=345 :!:
не открывает

Аватара пользователя
инжектор+
Майор
Майор
Сообщения: 1459
Зарегистрирован: 13 дек 2011, 01:52
Город: красная поляна
Авто: ASX S08 MT БЕЛЫЙ
:
Всегда готов
Благодарил (а): 100 раз
Поблагодарили: 199 раз

загорается "check engine"

#7

Сообщение инжектор+ » 12 май 2016, 15:44

voyager писал(а):Код ошибки был P0137

Для России:

Code No. P0137: Oxygen Sensor (rear) Circuit Low Voltage <Vehicles for Russia>


OPERATION



The sensor signal is inputted to the engine-ECU (terminal No. 40) from the oxygen sensor (rear) output terminal (terminal No. 3).
The engine-ECU (terminal No. 41) applies an offset voltage of 0.5 V to the oxygen sensor (rear) (terminal No. 4).
FUNCTION



The oxygen sensor (rear) converts the concentration of oxygen in the exhaust emission into a voltage and inputs the signal to the engine-ECU.
When the air-fuel ratio is richer than the theoretical air-fuel ratio, the oxygen sensor (rear) outputs a voltage of about 1 V. When it is leaner than the theoretical air-fuel ratio, it outputs a voltage of about 0 V.
In response to the signal, the engine-ECU controls the fuel injection amount so that the air-fuel ratio can be equivalent to the theoretical air-fuel ratio.
TROUBLE JUDGMENT


Check Conditions
Oxygen sensor (rear) offset voltage is more than 0.4 V and is less than 0.6 V.
Battery positive voltage is more than 11 V and is less than 16.5 V.
More than 3 minutes have passed since the engine starting sequence was completed.
Judgement Criterion
Oxygen sensor (rear) output voltage is less than 0.2 V for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION



None
PROBABLE CAUSES



Failed oxygen sensor (rear)
Open/short circuit or harness damage in oxygen sensor (rear) circuit or loose connector contact
Failed engine-ECU
DIAGNOSIS PROCEDURE


STEP 1. M.U.T.-III data list



Data list reference table (Refer to ).

Item AD: Oxygen sensor (rear)
Q. Is the check result normal?

Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Go to Step 2.
STEP 2. Connector check: D-38 oxygen sensor (rear) connector


Q. Is the check result normal?

Go to Step 3.
Repair or replace the connector.
STEP 3. Perform voltage measurement at D-38 oxygen sensor (rear) connector.



Disconnect connector, and measure at harness side.
Ignition switch: ON
Voltage between terminal No. 4 and earth.
OK: 0.4 - 0.6 V
Q. Is the check result normal?

Go to Step 7.
Go to Step 4.
STEP 4. Connector check: B-26 engine-ECU connector


Q. Is the check result normal?

Go to Step 5.
Repair or replace the connector.
STEP 5. Check harness between D-38 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.


note Before checking harness, check intermediate connectors A-17 and C-15, and repair if necessary.

Check earthing line for open/short circuit.
Q. Is the check result normal?

Go to Step 6.
Repair the damaged harness wire.
STEP 6. M.U.T.-III data list



Data list reference table (Refer to ).

Item AD: Oxygen sensor (rear)
Q. Is the check result normal?

Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Replace the engine-ECU.
STEP 7. Connector check: B-26 engine-ECU connector


Q. Is the check result normal?

Go to Step 8.
Repair or replace the connector.
STEP 8. Check harness between D-38 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.


note Before checking harness, check intermediate connectors A-17 and C-15, and repair if necessary.

Check earthing line for damage.
Q. Is the check result normal?

Go to Step 9.
Repair the damaged harness wire.
STEP 9. Perform voltage measurement at D-38 oxygen sensor (rear) connector.



Use special tool test harness (MB991658) to connect connector, and measure at pick-up harness.
Transmission: 2nd speed
Drive with wide open throttle
Engine: 3,500 r/min or more
Voltage between terminal No. 3 and earth.
OK:
The output voltage should be 1.1 - 1.5 V.
Q. Is the check result normal?

Go to Step 11.
Go to Step 10.
STEP 10. Check oxygen sensor (rear) itself.



Oxygen sensor check (Refer to ).
Q. Is the check result normal?


Check intermediate connectors A-17 and C-15, and repair if necessary. If intermediate connectors are normal, check and repair harness between D-38 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.

Check output line for short circuit.
Replace oxygen sensor (rear).
STEP 11. Check harness between D-38 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.


note Before checking harness, check intermediate connectors A-17 and C-15, and repair if necessary.

Check output line for open circuit and damage.
Q. Is the check result normal?

Go to Step 6.
Repair the damaged harness wire.





Yandex.Metrika ???????@Mail.ru??
MMC-Manuals.ru

Аватара пользователя
инжектор+
Майор
Майор
Сообщения: 1459
Зарегистрирован: 13 дек 2011, 01:52
Город: красная поляна
Авто: ASX S08 MT БЕЛЫЙ
:
Всегда готов
Благодарил (а): 100 раз
Поблагодарили: 199 раз

загорается "check engine"

#8

Сообщение инжектор+ » 12 май 2016, 15:45

Для остального мира :-)

Code No. P0137: Oxygen Sensor (rear) Circuit Low Voltage <Except vehicles for Russia>


OPERATION



The sensor signal is inputted to the engine-ECU (terminal No. 40) from the oxygen sensor (rear) output terminal (terminal No. 3).
The engine-ECU (terminal No. 41) applies an offset voltage of 0.5 V to the oxygen sensor (rear) (terminal No. 4).
FUNCTION



The oxygen sensor (rear) converts the concentration of oxygen in the exhaust emission into a voltage and inputs the signal to the engine-ECU.
When the air-fuel ratio is richer than the theoretical air-fuel ratio, the oxygen sensor (rear) outputs a voltage of about 1 V. When it is leaner than the theoretical air-fuel ratio, it outputs a voltage of about 0 V.
In response to the signal, the engine-ECU controls the fuel injection amount so that the air-fuel ratio can be equivalent to the theoretical air-fuel ratio.
TROUBLE JUDGMENT


Check Conditions
Oxygen sensor (rear) offset voltage is more than 0.4 V and is less than 0.6 V.
Battery positive voltage is more than 11 V and is less than 16.5 V.
More than 3 minutes have passed since the engine starting sequence was completed.
Judgement Criterion
Oxygen sensor (rear) output voltage is less than 0.2 V for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION



None
PROBABLE CAUSES



Failed oxygen sensor (rear)
Open/short circuit or harness damage in oxygen sensor (rear) circuit or loose connector contact
Failed engine-ECU
DIAGNOSIS PROCEDURE


STEP 1. M.U.T.-III data list



Data list reference table (Refer to ).

Item AD: Oxygen sensor (rear)
Q. Is the check result normal?

Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Go to Step 2.
STEP 2. Connector check: C-36 oxygen sensor (rear) connector


Q. Is the check result normal?

Go to Step 3.
Repair or replace the connector.
STEP 3. Perform voltage measurement at C-36 oxygen sensor (rear) connector.



Disconnect connector, and measure at harness side.
Ignition switch: ON
Voltage between terminal No. 4 and earth.
OK: 0.4 - 0.6 V
Q. Is the check result normal?

Go to Step 7.
Go to Step 4.
STEP 4. Connector check: B-26 engine-ECU connector


Q. Is the check result normal?

Go to Step 5.
Repair or replace the connector.
STEP 5. Check harness between C-36 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.


note Before checking harness, check intermediate connector A-17, and repair if necessary.

Check earthing line for open/short circuit.
Q. Is the check result normal?

Go to Step 6.
Repair the damaged harness wire.
STEP 6. M.U.T.-III data list



Data list reference table (Refer to ).

Item AD: Oxygen sensor (rear)
Q. Is the check result normal?

Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Replace the engine-ECU.
STEP 7. Connector check: B-26 engine-ECU connector


Q. Is the check result normal?

Go to Step 8.
Repair or replace the connector.
STEP 8. Check harness between C-36 (terminal No. 4) oxygen sensor (rear) connector and B-26 (terminal No. 41) engine-ECU connector.


note Before checking harness, check intermediate connector A-17, and repair if necessary.

Check earthing line for damage.
Q. Is the check result normal?

Go to Step 9.
Repair the damaged harness wire.
STEP 9. Perform voltage measurement at C-36 oxygen sensor (rear) connector.



Use special tool test harness (MB991658) to connect connector, and measure at pick-up harness.
Transmission: 2nd speed
Drive with wide open throttle
Engine: 3,500 r/min or more
Voltage between terminal No. 3 and earth.
OK:
The output voltage should be 1.1 - 1.5 V.
Q. Is the check result normal?

Go to Step 11.
Go to Step 10.
STEP 10. Check oxygen sensor (rear) itself.



Oxygen sensor check (Refer to ).
Q. Is the check result normal?


Check intermediate connector A-17, and repair if necessary. If intermediate connector is normal, check and repair harness between C-36 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.

Check output line for short circuit.
Replace oxygen sensor (rear).
STEP 11. Check harness between C-36 (terminal No. 3) oxygen sensor (rear) connector and B-26 (terminal No. 40) engine-ECU connector.


note Before checking harness, check intermediate connector A-17, and repair if necessary.

Check output line for open circuit and damage.
Q. Is the check result normal?

Go to Step 6.
Repair the damaged harness wire.





Yandex.Metrika ???????@Mail.ru??
MMC-Manuals.ru

Аватара пользователя
mobileman
Майор
Майор
Сообщения: 1114
Зарегистрирован: 29 окт 2012, 13:37
Город: Москва
Авто: Lancer X, Audi A3
Пробег: 110000
Прошлый авто: Lancer IX
:
Золотая звезда I степени Золотые руки
Благодарил (а): 141 раз
Поблагодарили: 391 раз

загорается "check engine"

#9

Сообщение mobileman » 12 май 2016, 15:49

voyager
для начала проверьте проводку датчика под днищем на предмет повреждения изоляции...

Аватара пользователя
инжектор+
Майор
Майор
Сообщения: 1459
Зарегистрирован: 13 дек 2011, 01:52
Город: красная поляна
Авто: ASX S08 MT БЕЛЫЙ
:
Всегда готов
Благодарил (а): 100 раз
Поблагодарили: 199 раз

загорается "check engine"

#10

Сообщение инжектор+ » 12 май 2016, 15:50


Аватара пользователя
hardman
Старший лейтенант
Старший лейтенант
Сообщения: 548
Зарегистрирован: 05 окт 2012, 16:47
Город: Москва
Авто: ASX S11 Dark Blue
Пробег: 297000
Прошлый авто: KIA CeeD hatchback KIA Rio JB, Opel Astra
Благодарил (а): 38 раз
Поблагодарили: 74 раза

загорается "check engine"

#11

Сообщение hardman » 12 май 2016, 16:52

Коллеги, а если человек с английским не дружит?:) форум мне кажется на то он и форум чтобы дать по возможности совет а не отсылать лопатить ERROR LIST :pl1:
Вот такие дела....

Аватара пользователя
mobileman
Майор
Майор
Сообщения: 1114
Зарегистрирован: 29 окт 2012, 13:37
Город: Москва
Авто: Lancer X, Audi A3
Пробег: 110000
Прошлый авто: Lancer IX
:
Золотая звезда I степени Золотые руки
Благодарил (а): 141 раз
Поблагодарили: 391 раз

загорается "check engine"

#12

Сообщение mobileman » 12 май 2016, 19:32

hardman писал(а):Коллеги, а если человек с английским не дружит?:)

Существует масса онлайн-переводчиков в интернете. Да, многие из них переводят "коряво", но уловить смысл про типовые причины возникновения кода неисправности вполне возможно.
P.S. Советов можно дать много....Проверить проводку датчика. Если изоляция сигнальных проводов повреждена и будет "коротить" на корпус авто, то можно словить P 0137.
Можно проверить опорное напряжение, которое ЭБУ двигателя выдает на датчик. Оно должно быть ~0.5 v... Сделать это можно с помощью мультиметра в подкапотном блоке предохранителей, измерив напряжение на соответствующих проводах белого большого разъема при включенном зажигании.Схемы из мануала, ссылку на который уже дали - в помощь.

Аватара пользователя
инжектор+
Майор
Майор
Сообщения: 1459
Зарегистрирован: 13 дек 2011, 01:52
Город: красная поляна
Авто: ASX S08 MT БЕЛЫЙ
:
Всегда готов
Благодарил (а): 100 раз
Поблагодарили: 199 раз

загорается "check engine"

#13

Сообщение инжектор+ » 12 май 2016, 19:57

Если человек не дружит с английским, не разбирается в устройстве авто, никогда не пользовался мультиметром(и не хочет этому научиться) - совет может быть один: ищите хорошего диагноста. :roll:



Вернуться в «Вопросы по электрике»



Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и 25 гостей